TL;DR — A roll-off hoist runs at least two hydraulic cylinders: a lift cylinder that tilts the frame up to about 49 to 52 degrees, and a reeving cylinder that drives the cable winch pulling the container onto the rails. Heavy jib and locking cylinders show up on hooklift-style units. Bore and rod are not interchangeable across those functions, and the working pressure is the first number to pin down. A 60,000 lb cable hoist is a 6-inch-bore machine around 2,000 PSI; a 70,000 lb hoist needs a 7-inch bore. Match that, then measure pin centers, and the replacement drops in without rework.

Three cylinders, three jobs

People call the whole assembly "the hoist cylinder," but a roll-off truck rarely has just one. The lift cylinder carries the tilt, the reeving cylinder carries the cable pull, and a jib or locking cylinder handles the container latch. Each sees a different load profile and a different cycle count.

The lift cylinder works against the full weight of a loaded container at the worst mechanical angle. The reeving cylinder spends its life under cable tension, which stays high even when the frame is nearly level. The jib cylinder only moves at the start of a cycle, but it is the one that fails when a container is picked up off-center.

Order them as separate line items. A supplier that asks for one "hoist cylinder" size without asking which function is guessing.

Start from working pressure, not from bore

Bore follows pressure. A roll-off circuit that runs 2,000 PSI can hold a 60,000 lb container with a 6-inch bore. Push the same 6-inch tube onto a 4,200 PSI circuit and the rod seal, gland and welds are all running beyond what they were designed for.

Verified OEM references spread wider than most fleets expect. A Galbreath U5-OX runs around 1,850 PSI. A Stellar Shuttle32 runs 4,200 PSI. Same bore can appear in both, but the tube wall, rod finish and seal compound are not the same part.

Read the hoist nameplate first. Then match the cylinder to that number. Guessing a "standard" pressure is how a replacement cylinder gets built wrong from the first weld.

Hoist class Lift / reeving cylinder Typical working pressure Max dump angle
Medium duty, 20,000 lb 5" bore × 2.5" rod × 80" (lift); 5.5" × 3" × 84" (reeving) ≈ 2,000 PSI ≈ 52°
Heavy duty, 60,000 lb 6" bore × 3" rod × 84" stroke 2,000 PSI ≈ 49°
Heavy duty, 70,000 lb 7" bore × 3" rod × 84" stroke 2,000 PSI ≈ 49°

Figures collated from published North American cable-hoist specifications (Dragon, Ranco and EO Trailer build sheets). Bore, stroke and pressure vary by hoist model — confirm against your nameplate before ordering. HCIC quotes from your drawing or sample inside 48 hours.

The pin-center measurement most people skip

Bore and stroke are easy to read off a worn cylinder. Retracted pin-to-pin length is where the rework starts. A cylinder that is 10 mm shorter or longer than the original will not bolt into the same mounts, and shimming a hoist cylinder is never a long-term fix.

Measure from the center of one mounting eye to the other with the rod fully retracted. Record the pin diameter and the inside width of the clevis at the same time. These three numbers, plus port thread and location, decide whether a replacement is a drop-in or a fabrication job.

Send a photo with the measurements. A drawing is better. Either beats a part number from a faded sticker.

Why the reeving cylinder wears out first

On a cable hoist, the reeving cylinder runs the winch that spools the container up the rails. It spends more time under sustained cable tension than the lift cylinder spends under tilt load, and it cycles more often on every single pick-up. That is why a reeving cylinder often needs replacement before the lift cylinder on the same truck.

Look for rod seal weeping first, then drift when the cable should hold. A reeving cylinder that lets the container creep back down the rails under load has an internal piston-seal bypass, and a load-holding or counterbalance valve belongs on that circuit. Our team treats reeving and lift cylinders as separate rebuild decisions for this reason.

Single or double acting, and the counterbalance question

A roll-off lift cylinder is double acting in practice: the frame has to come back down under control, not drop under gravity with a loaded container on it. That return stroke is where a counterbalance valve earns its place. Without one, a failed hose or a lost pump lets the body slam down.

Reeving cylinders follow the same rule. Cable tension must be released smoothly, and a counterbalance valve set slightly above the maximum induced load keeps the drum from free-spooling. Ask your supplier whether the valve is integrated or remote — integrated is easier to plumb and harder to lose on a rebuild.

How I confirm a hoist cylinder before quoting

  1. Read the hoist nameplate and record the system pressure and rated capacity.
  2. Identify the function — lift, reeving, jib, tilt or locking — and order them as separate items.
  3. Measure bore and rod with calipers, not from a guess, and record stroke full-to-full.
  4. Measure retracted pin-to-pin, pin diameter and clevis width.
  5. Note port threads (SAE O-ring or NPT) and port position.
  6. Confirm single or double acting, and whether a counterbalance valve is fitted.

Six numbers and one photo usually turn a vague "I need a roll-off cylinder" into a buildable drawing.

When replacement beats a reseal

A rod that is scored or bent past polish, a barrel that is scored inside the bore, or a gland that has been hammered oval are all replacement calls. Resealing one of those returns the leak in a few hundred cycles and leaves the real problem in the tube. Our refuse truck cylinders and hooklift and container handling cylinders are built to ISO 6020 and 6022 geometry, pressure-tested to 3,000 PSI before dispatch, and carry an 18-month warranty from shipment.

When the part number is gone, our custom and OEM replacement service works from a drawing or the six measurements above — quote inside 48 hours, one sample minimum, 45 to 60 days for the first article. The same tilt-and-hold logic applies to dump trailers, where the bore steps are larger and the return is usually gravity; our transport division covers that case on hcictec.com. If your nameplate reads in bar and your gauge reads in PSI, use the pressure converter before comparing anything.

Frequently asked questions

What size cylinder does a roll-off hoist use?

A 60,000 lb cable hoist typically uses 6-inch bore by 3-inch rod lift and reeving cylinders with about an 84-inch stroke. A 70,000 lb hoist moves to a 7-inch bore. Medium-duty 20,000 lb units run 5 to 5.5-inch bores. Confirm against your hoist model, not a catalog guess.

How much pressure does a roll-off hoist run?

Most cable hoists run 2,000 PSI. Verified OEM references range from 1,850 PSI (Galbreath U5-OX) to 4,200 PSI (Stellar Shuttle32). Set the relief to the hoist nameplate and match the cylinder to that value, because a 2,000 PSI tube will not survive a 4,200 PSI circuit.

What is the difference between a lift cylinder and a reeving cylinder?

The lift cylinder tilts the frame up to about 49 to 52 degrees. The reeving cylinder runs the cable winch that pulls the container on and off the rails. They look alike but carry different loads and cycle counts, so specify them separately.

Can HCIC build a replacement roll-off hoist cylinder?

Yes. Send the bore, rod, stroke, retracted pin-to-pin length, pin diameter, port threads and working pressure, or a drawing and photos if the part number is obsolete. Minimum order is one sample, first-article lead time is 45 to 60 days, and every cylinder carries an 18-month warranty.